Shop Applications About us Support & feedback Product literature Blog FAQ Careers Contact
Measurement technologies
Oval GearHelical RotorPlastic HelicalTurbineElectromagneticVortexSwirlThermal MassFuel Consumption MeterVehicle Fuel Management
Policies
Terms & ConditionsTrademarkShipping PolicyPrivacy PolicyBilling TermsCancellation PolicyRefund & Returns
Get a quote Call us

Your Cart

Subtotal₹0
Proceed to Checkout →
Thermal Mass Velocity Flow Meter — real BROIL product photograph
HEAT TRANSFER — VELOCITY FLOW METER

Thermal Mass Velocity Flow Meter

Heat lost to the gas becomes the flow rate.

The thermal mass flow meter operates on the principle of thermal dispersion — gases conduct heat differently than other substances. The meter carries two temperature sensors: a heated sensor and a reference sensor, maintaining a constant temperature difference between them. As gas flows through the meter it cools the heated sensor, and the flow rate is directly proportional to the amount of cooling. Measuring the temperature difference between the two sensors gives the gas flow rate directly.

Sensor housing
SS-316 / Hastelloy / PTFE coated
Velocity
±0.1 ~ 100 Nm/s
Accuracy (standard position)
±1%
Fluid & ambient temperature
-20 to 240°C
Where it is used

Markets & areas of application

Primarily used for measuring the flow of gases — air, natural gas, nitrogen and other process gases — without needing recalibration for composition changes. Common in chemical processing, HVAC systems and environmental monitoring.

Click any industry to see the full product list for it, or tell us your process and we will confirm the match.

Why choose it

Advantages

✓Direct mass flow measurement, critical where mass flow is a key parameter
✓No moving parts in contact with the fluid
✓High turndown ratio for wide flow-rate ranges
✓Fast response time, real-time measurement
✓Low pressure drop
✓Covers DN15 to DN4000, from 1 to 7,00,000 Nm³/h
✓No recalibration needed when gas composition changes
Build & specification

General Specification

Sensor housing
SS-316 / Hastelloy / PTFE coated
Velocity
±0.1 ~ 100 Nm/s
Accuracy (standard position)
±1%
Fluid & ambient temperature
-20 to 240°C
Connection
Insertion type / Flange end
Before you configure

Frequently asked questions

Why choose Thermal Mass over Vortex or Swirl for gas?+

Thermal Mass reads true mass flow directly from the gas's heat-loss characteristics, with no need to recalibrate when gas composition changes — Vortex and Swirl are volumetric and suit a narrower set of gas types at higher velocities.

What's the accuracy and range?+

±1% accuracy, covering velocities of ±0.1 to 100 Nm/s and pipe sizes from DN15 to DN4000, 1 to 7,00,000 Nm³/h.

What temperature range does it handle?+

-20°C to 240°C, in SS-316, Hastelloy or PTFE-coated sensor housings depending on the gas's corrosivity.

Insertion type or flange end — which do I need?+

Insertion type suits large ducts where a full flange run isn't practical; flange end suits smaller, standard pipe runs. Tell us your duct or pipe size and we'll confirm which fits.

How fast does it respond to changes in flow?+

Fast — the sensor has no moving parts and a quick thermal response, so it tracks real-time changes rather than averaging over a long window.

Does moisture or condensation in the gas throw off the reading?+

Yes, if it reaches the sensor. Condensed droplets hitting the heated element pull heat away much faster than dry gas does, so the meter reads a spike that isn't real flow. If your gas is anywhere near saturated, the fix is installation, not the sensor: keep the line above the dew point where possible, mount the sensor angled so any condensate drains away rather than pooling on it, or fit a knockout drum upstream to pull moisture out before the gas reaches the meter. Tell us if your gas is wet and we'll advise on mounting.

Do I need to recalibrate if the gas composition changes?+

Yes — the meter is calibrated against the thermal properties of the specific gas (or gas mixture) you tell us you're measuring, because different gases carry heat away from the sensor at different rates for the same mass flow. A consistent gas like nitrogen or dry compressed air rarely needs attention. A variable mixture like biogas, where methane and CO2 content can drift, needs the composition range confirmed upfront so we calibrate for the actual swing, not just a single snapshot.

Model range

Choose your model

DN (mm)Max Flow Rate (Nm³/hour)
1565
25175
32290
40450
50700
651200
801800
1002800
1254400
1506300
20010000
25017000
30025000
40045000
50070000
600100000
700135000
800180000
900220000
1000280000
1200400000
1500600000
2000700000
Build your unit

Configure it, then get a quote

Choose the options you need. Every selection is included automatically when you send the request — so the price you get back is for the unit you actually want.

Please enter your name.
Please enter a valid email address.
Please enter a phone number.

Goes to info@broiltech.com. An engineer replies within one working day.

Related technology

You might also need

WhatsApp us Call an engineer